Hinderer Eklipse 3.0 Fullered Harpoon Spearpoint Non-Flipper Blue G10 Working Finish Titanium Magnacut Folding Knife (3.10" Blade)
Model #:
HK-1985
Brand:
Hinderer Knives
$425.00
In stock
(Usually Ships in 24-48 Hours)
Related Categories
Details
Built for daily cutting with hard-use backbone, the Hinderer Eklipse 3.0 Non-Flipper in Blue G10 wears Working Finish from blade to liners. Its Magnacut harpoon spearpoint flicks open off the thumb stud.
- Magnacut Blade Steel - Magnacut is a stainless powder steel that pairs outstanding rust resistance with real toughness. It holds an edge well too, and it carries daily cutting a long way between sharpenings.
- Fullered Harpoon Spearpoint - The point sits centered in line with the handle. That alignment keeps piercing cuts controlled and predictable. A fuller sits in each face of the blade just below the spine.
- Non-Flipper Thumb Stud Opening - There is no flipper tab on this build. The thumb stud alone launches the blade, and it swings free enough on its bearings to flick fully open with one push.
- Working Finish Throughout - Blasted and then tumbled, the Working Finish runs across the blade and both titanium liners in one flat gray. Blue G10 scales sit over the liners in a smooth matte finish for an all-business color scheme.
The Hinderer Eklipse 3.0
Rick Hinderer drew the Eklipse with straighter, more linear lines than his XM-18. The Eklipse 3.0 packs that design into a compact handle built on thick titanium liners and keeps the toughness of the larger model. With the blade open, the tip lines up with the center of the handle, and that alignment makes the knife feel light and easy to steer. Double finger grooves and a sloping underside shape the grip, and a jimped thumb ramp on the blade gives the thumb a firm place to push when a cut takes pressure.
- Liner Lock - The lock-side titanium liner is heavier than its partner, and it engages early on the blade tang. The open blade sits with no play in any direction, side to side or up and down.
- Thumb Stud Blade Stop - The thumb stud does double duty. Working with a stop pin, it serves as the blade stop that halts the blade at full open. One part both starts the swing and ends it.
- Tri-Way Pivot System - The pivot ships running on bearings. Phosphor bronze and Teflon washers come included as alternates. Swap them in to tune the action for the environment the knife works in.
- Firm Detent - The detent holds the blade shut with real resistance. Push past it on the thumb stud and the stored pressure releases the blade with momentum behind it.
- Two Finger Grooves - Two grooves shaped into the underside of the handle give the index and middle fingers their own seats. They lock the grip in place and stop the hand from sliding forward toward the edge.
- Aggressive Jimping - Sharp jimping teeth line the blade spine near the pivot and the tail of the handle spine. They bite into the thumb for firm traction when a cut calls for pressure.
- Titanium Pocket Clip - The titanium clip mounts for tip-up, right-side carry only. Left-handed and tip-down carriers should plan around that single position before buying.
Specifications
| Knife Action | Manual |
|---|---|
| Brand | Hinderer Knives |
| Designer(s) | Rick Hinderer |
| Overall Length | 7.41" |
| Blade Length | 3.10" |
| Sharpened Length | 2.82" |
| Blade Thickness | 0.14" |
| Blade Material | MagnaCut |
| Blade Type | Stainless |
| Blade Grind | Flat |
| Blade Finish | Blasted, Tumbled |
| Opening Method | Thumb Stud/Disc |
| Pivot | Hinderer Tri-Way Pivot |
| Lock Type | Liner Lock |
| Closed Length | 4.31" |
| Handle Thickness | 0.50" |
| Handle Material | G10 |
| Hardware | Titanium |
| Liner(s) | Titanium |
| Clip Material | Titanium |
| Clip Position | Tip-Up |
| Weight | 3.90 oz. |
| Condition | New |
| Country of Origin | United States |









